Showing results: 136 - 150 of 201 items found.
-
DATS-solo -
Prosig Ltd
The DATS-solo is a pocket-sized, ultra portable, high quality, 24-bit data acquisition system. The fully integrated DATS software provides options for acoustic & vibration testing, rotating machinery analysis, NVH tests, hammer impact analysis, resonance testing and modal analysis.
-
KD-2768 -
King Design Industrial Co., Ltd.
Drop tester is applied to test the anti-vibration, covering-protection capability of packaging material, or product’s impact-resisting capability to determine the improvement parts of related packing design, material and structure. It contribute to promote the packing material and product’ strength. According to the result of packing drop test, you can judge whether the product has reach the required strength encountered in future. Through doing the drop testing of product independently, you’ll know its affordability to withstand external impact and assess the damage.
-
Keystone Compliance
Drop testing, per MIL-STD 202 Method 203, is used to determine the effects on component parts of random drops tested and repeated impact due to handling, shipping, and other field service conditions. This drop testing is an accelerated test designed to indicate structural and mechanical weaknesses of types not necessarily detected in shock and vibration tests. Package drop testing can help determine the survivability of a product’s packaging and help manufacturers identify potential warranty issues from poor packaging or improper handling instructions.
-
Keystone Compliance
Altitude testing, also referred to as low pressure testing, per MIL-STD 810 Method 502.4, is performed to ensure that equipment can withstand and operate in a low pressure test or high altitude test environment. Altitude testing is intended to be used for air shipment of material in a plane, equipment designed for installation at high ground elevations and explosive decompression due to aircraft damage. Manufacturers of any device that is transported by air should consider the impact high altitude testing or low-pressure testing could have on their products. A low pressure test can simulate the problems high altitude can create such as:
-
Wewon Environmental Chambers Co, Ltd.
In Wewon, We have 2 powerful Vibration Testing Equipment. The Vibration Testing Equipment A is : EV210H0808VCSusb-E; The Vibration Testing Equipment B is: EV232H0809VCSusb-E. Technical parameters as below blank forms mentioned, The mainly difference is Sine Excitation Force, Frequency Range, Vibration Table’s size. Application for Vibration Test Equipment : The vibration test is to inspire or impact a part or device to see how it reacts in a real environment. The application of vibration test is very extensive, from the circuit board, aircraft, ships, rockets, missiles, automobiles and household appliances and other industrial products.
-
SHPB -
Advance Instrument Inc.
Advance Instrument (AI) having solid knowledges and experiences in this field of materials measuring and testing, has developed a comprehensive suite of services providing test, modelling and validating high strain rate behavior of polymeric materials. AI can test tensile and compressive behavior of a wide variety of polymeric materials over strain rates ranging from 10(-3)/s to 10(3)/s combining conventional test techniques with advanced, high strain rate techniques using Split Hopkinson Pressure Bar (SHPB) and instrumented impact testing.
-
HILT Kit -
ATSI
The HILT-Kit is easy to use, with quick and accurate tools designed to test and measure the parameters of inductive loops used in the Traffic Signal, Vehicle Data Collection, and Parking industries. The test kit is housed in an impact resistant case with a set of 6 foot test leads and adapters. The sturdy, injection molded plastic carrying case is custom designed to hold the HILT-9000 and its accessories, as well as the LF-22 Loop Finder and AEMC 6527 Digital Megohmmeter for a complete loop analysis kit. (The HILT can be ordered by itself, without the Loop Finder and Megohmeter as the HILT-9000)
-
Shanghai Linpin Instrument
Single-wing Drop Test Machine Simulate the drop conditions of packaged products when different faces, edges and corners fall to the ground from different heights, thus to understand the damage of the product and evaluate the drop height and impact resistance that the packaging materials can endure while falling down, so as to improve and optimize package design according to actual conditions of the product and national standard range.
-
Carl Zeiss AG
Is your product heat-resistant? Throughout their useful lives, technical products are subject to a multitude of environmental influences, e.g., heat, cold, oscillations or impacts. This influences their functioning and length of service life. We can find out how the effect and cause are interrelated with an environmental simulation. We will test your products under specific environmental conditions and help you to optimize them for sustainable product development.
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
KRD60 series -
CME Technology Co. Ltd.
KRD60 Series 3 DOF simulation table simulates various mechanical, electrical, and electronic products installed on ships, seaplanes, and other equipment to perform sway and tilt tests to determine the ability and structural integrity of the product to withstand severe sway and tilt requirements. The tilt test is mainly applicable to large-angle tilt caused by ship damage, manipulation, imbalance in loading and unloading, and wind. The sway test is mainly applicable to long-term swaying of the ship due to external forces such as wind and waves, which must be maintained normally or products that work reliably, and products that have a significant impact on their performance in a rocking environment.
-
Benz Co., Inc.
Has automated the test process with microprocessor-controlled data acquisition. Designed to provide the expected internal bond strength for various types of paper, coated products and paperboard, this instrument measures the impact energy imparted to the specimen. The machine consists of a base, sample-preparation press, tape dispenser, dual-range pendulum (0 to 0.325 ft. lbs. and 0 to 0.650 ft. lbs.) and Digital Display. Internal Bond software is available.
-
LS600 -
Lisun Electronics Inc.
• The standard LS600 has 1 Group which has 8 channels. That means LS600 can test 8 LEDs separately at one time. (Optional: it expand to 8 Groups which can test 64 LEDs separately at one time) • Aging Functions: Constant Current, Impact Pulse, On/Off Mode • Output current: 1~1000mA (Special Order Available) • Output voltage: 5V(Special Order Available) • Output frequency: 1~3000Hz, Duty Ratio: 1%-99% • Range of on-off circle: 0~9999h/59m/59s
-
KRD41 series -
CME Technology Co. Ltd.
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
KRD40 series -
CME Technology Co. Ltd.
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
